Rubber Lined Centrifugal Suction Slurry Pump
Name: BHR Rubber Slurry Pump
Pump Type: Centrifugal
Power: Motor/Diesel
Discharge Size: 1-18 inch
Capatiy: 0-1000(l/s)
Head: 0-70m
Description:
BH(R) series centrifugal slurry pumps and spare parts can fully interchage with world famous brand. These pumps are of heavy-duty construction, designed for continuous pumping of highly abrasive and corrosive slurries. They feature a wide choice of replaceable abrasion resistant metal or moulded elastomer casting liners and impellers, which are all interchangeable within a common costing assembly.
Typical Application:
Minerals Flotation Processing
Electric Factory Coal Preparation
Coal Washing
Chemical Medium Processing
Effluent Handling
Sand and Gravel Handling
| Pump Model |
Allowable Max. Power(kw) |
Clear Water Performance |
|
| capacity Q |
Head H(m) |
speed n(r/min) |
Max.eff. η% |
NPSH (m) |
Impeller Dia(mm) |
| m3/h |
l/s |
| 1.5/1B-BHR |
15 |
10.8-25.2 |
3-7 |
7-52 |
1400-3400 |
35 |
|
|
| 2/1.5B-BHR |
15 |
25.2-54 |
7-15 |
5.5-41 |
1000-2600 |
50 |
2.5-5.5 |
178 |
| 3/2C-BHR |
30 |
36-75.4 |
10-21 |
13-39 |
1300-2100 |
|
2-4 |
213 |
| 4/3C-BHR |
30 |
79.2-180 |
22-50 |
5-34.5 |
800-1800 |
59 |
3-5 |
245 |
| 4/3D-BHR |
60 |
| 6/4D-BHR |
60 |
144-324 |
40-90 |
12-45 |
800-1350 |
65 |
3-5 |
365 |
| 6/4E-BHR |
120 |
| 8/6E-BHR |
120 |
324-720 |
90-200 |
7-49 |
400-1000 |
65 |
5-10 |
510 |
| 8/6R-BHR |
300 |
| 10/8ST-BHR |
560 |
540-1188 |
150-330 |
12-50 |
400-750 |
75 |
4-12 |
|
| 12/10ST-BHR |
560 |
720-1620 |
200-450 |
7-45 |
300-650 |
80 |
2.5-7.5 |
|
| 14/12ST-BHR |
560 |
1152-2520 |
320-700 |
13-14 |
300-500 |
79 |
3-8 |
|
| 16/14TU-BHR |
1200 |
1368-3060 |
380-850 |
11-63 |
250-550 |
79 |
4-10 |
1067 |
Slurry Pump Main parts:
• Impeller - front and rear shrouds have pump out vanes that reduce recirculation and seal contamination.
Hard metal and molded rubber impellers are complete interchangeable. Cast in impeller threads require no inserts or nuts. High efficiency and high head designs are also available.
• Liners - Easily replaceable liners are bolted, not glued, to the casing for positive attachment and ease of maintenance. Hard metal liners are completely interchangeable with pressure molded elastomers. Elastomer
seal rings back all liner joints.
• Throat Bush - Wear is reduced and maintenance simplified by the use of tapered mating faces to allow positive accurate alignment during assembly and simple removal.
• Bearing assembly - A large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame.
Slurry Pump Spare Parts
Slurry pump wet end parts mainly include Impeller, volute liner, Casing, shaft, throat bush, wear plate, case, cover, stuffing box, lantern restrictor, cover plate bolt, throat bush, shaft sleeve, cover plate liner, frame plate liner...
1.centrifugal slurry pumps and spare parts can fully interchange with world famous brand.
2.These pumps are of heavy-duty construction, designed for continuous pumping of highly abrasive and corrosive slurries.
3. They feature a wide choice of replaceable abrasion resistant metal or moulded elastomer elastomer elastomer casting liners and Impellers, which are all interchangeable within a common casting assembly.
4.Wear -resistant Metal Liner and Rubber Liner available
5.Seal Type: gland seal , impeller seal and mechanical seal
6.Can be installed in multistage series
7.easy to maintenance
The properties of the rubber material:
We have variety of natural rubber and elastomers, which can be used for pumping corrosive or acid slurries. But the rubber material is not suitable for slurries which contain sharp solids.
When the slurries contain fine particles, the rubber material features good performance of wear resistant.
Horizontal Centrifugal Slurry Pump
1. Durable slurry pump used for mines and industry solids pumping.
2. Wearing parts are made of Anti-abrasive ultral Cr alloy or rubber.
3. Slurry pump drive module design which makes the spare parts can be changed easily
4. Designed and built for long time with low maintenance for the Heavy brand slurry pump
5. Equipped the electric motor or diesel engine with slurry pump according to your requirement
6. Long service life for the wet parts of slurry pump.
The Features:
1. The wet parts for slurry pump are made of wear-resistant chromium alloy.
2. Slurry pump's bearing assembly use cylindrical structure,adjusting the space between impeller and front liner easily, they can be removed completely when being repaired. Bearing assembly use grease lubrication.
3. The shaft seal could use the packing seal, expeller seal and mechanical seal.
4. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
5. There are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, frequency conversion drive devices for the slurry pump.
6. Wide performance, good NPSH and high efficiency. The slurry pump can be installed in multistage series to meet the delivery for long distance.
FAQ
1. What Products does BODA pump mainly produce?
BODA mainly Produce Slurry Pump, Gravel sand Pump, Dredging Pump, Centrifugal water pump and Spare Parts. Not only Pump parts, but also others wear casting parts if there is drawing or sample.
2. Is BODA direct factory or trader?
BODA own foundry workshop, Machining Workshop, and Assembly workshop.
Welcome to visit our factory anytime.
3. The Min MQQ
The MQQ is one pcs spare parts or one set bare pump
4. What information is required for quotes?
If you need the spare parts, we need to know the parts Code and material.
If you need the whole pump set, we need to know the usage? The flow, head, and SG, Corrosive or not? The more detailed the better.
Welcome to Contact Me
Shijiazhuang Boda Industrial Pump Co.,Ltd : alisa
Audited Supplier 
Audited Supplier 
){kind=link}
){kind=link}